Sewage Lifting Station

Product Details:

• Polyethylene container with 350 litres capacity and up to 175 litres switching volume
• Vortex pump with large solids handling
• Mechanical seal and shaft seal with intermediate oil chamber
• Pump housing with cast-on outlet bend DN 100
• Lateral inlet with loose-type flange DN 100
• Additional connection 1 ½“ for manual diaphragm pump
• Air vent with loose-type flange DN 100 (Ø 110 mm)
• Operation temperature max. 55°C
• Operating mode S3 – 25%
• Protection grade IP 57 – temporarily submersible

Product Details:

• Polyethylene container with 140 litres capacity and up to 70 litres switching volume
• Vortex pump with high efficiency
• Mechanical seal and shaft seal with intermediate oil chamber
• Inlets: 2 x DN 100
• Additional connections 1 ½“ for manual diaphragm pump
• Air vent DN 70 (Ø 75mm)
• Operation temperature max. 55°C
• Operating mode S3 – 25%
• Protection grade IP 68 – fully submersible

Product Details:

• Polyethylene container with 480 litres capacity and up to 270 litres switching volume
• Vortex pump with large solids handling
• Mechanical seal and shaft seal with intermediate oil chamber
• Pump housing with cast-on outlet bend DN 100
• Lateral inlet with loose-type flange DN 100
• Additional connection 1 ½“ for manual diaphragm pump
• Air vent with loose-type flange DN 100 (Ø 110 mm)
• Operation temperature max. 55°C
• Operating mode S3 – 25%
• Protection grade IP 57 – temporarly submersible

Product Details:

• Polyethylene container with 55 litres capacity and up to 45 litres switching volume
• Vortex pumps with high efficiency and low operation noise
• Mechanical seal and shaft seal with intermediate oil chamber
• Inlets: 3 x DN 100, 3 x DN 50, 1 x DN 50/100
• Additional connections 1 ½“ for manual diaphragm pump
• Air vent DN 70 (Ø 75mm)
• Operation temperature max. 55°C
• Operating mode S3 – 25%
• Protection grade IP 68 – fully submersible

Product Details:

• Polyethylene container with 200 litres capacity and up to 100 litres switching volume
• Vortex pumps with high efficiency
• Mechanical seal and shaft seal with intermediate oil chamber
• Inlets: 2 x lateral DN 100, 1 x top DN 100/DN 150
• Additional connections 1 ½“ for manual diaphragm pump
• Air vent DN 100 (Ø 110mm)
• Operation temperature max. 55°C
• Operating mode S3 – 25%
• Protection grade IP 68 – fully submersible

Product Details:

• As Lifting unit for grease separators.
• Polyethylene container with 135 litres capacity and up to 75 litres switching volume
• Simplex units with submersible waste water pump ZPK with float switch
• Duplex units with 2 pumps ZPK and control unit with pneumatic level control ZPS2
• Motor housing and shaft made of stainless steel, suction strainer, impeller and pump housing made of polypropylene
• Piping made of PVC with external non-return valves and pressure outlet 1 ¼“ FPT
• Operation temperature 40°C (short-term 90°C)
• Protection grade IP 57 – temporary submersible

Product Details:

• Polyethylene container with 35 litres capacity and up to 20 litres switching volume
• Built-in waste water pump ZPK with float switch
• Connection for air vent and cable gland DN 50 (HT)
• Inlet connection piece DN 50 is included – installable by drilling a hole in the container
• Pressure outlet 1 ¼“ with integrated non-return valve
• Operation temperature 40°C (short-term 90°C)
• Protection grade IP 68 – fully submersible

Product Details:

• Polyethylene container with 480 litres capacity and up to 270 litres switching volume
• Single-channel impeller pump with fibre cutting insert and large solids handling
• Mechanical seal (up to 4kW) or chilled casting seal (> 5 kW) and shaft seal with intermediate oil chamber
• Pump housing with flanged outlet bend DN 100
• Lateral inlet with loose-type flange DN 150
• Additional connection 1 ½“ for manual diaphragm pump
• Air vent with loose-type flange DN 100 (Ø 110 mm)
• Star-delta-start for 7,5 kW unit
• Operation temperature max. 55°C
• Operating mode S3 – 25%
• Protection grade IP 57 – temporarly submersible

Product Details:

• Optimized high-performance cutting system made of corrosion-resistant special steel 1.4112 with particular high hardness, wear resistance and cutting performance
• Tank made of ABS for direct connection to a free-standing toilet with minimum inlet height
• Tank ventilation via activate carbon filter; optional ventilation via DN 40 pipe
• Robust, wet-installed pump
• Integrated alarm signal in case of malfunction
• Pressure outlet 11/4″ FPT with integrated non-return valve on top; outlet horizontal or vertical (90° bend)
• Max. medium temperature 40°C – short-term max. 60°C protection grade IP 68 – fully submersible